| Standard No |
Title of Standard |
|
| EN 1:1998 |
Flued oil stoves with vaporizing burners |
| EN 10001:1991 |
Definition and classification of pig-irons |
| EN 100012:1996 |
Harmonized system of quality assessment for electronic components. Basic specification. X-ray inspection of electronic components |
| EN 100014:1992 |
Harmonized system of quality assessment for electronic components. Basic specification: CECC assessed process average procedure (60% confidence limit) |
| EN 100015-2:1994 |
Basic specification. Protection of electrostatic sensitive devices. Requirements for low humidity conditions |
| EN 100015-3:1994 |
Basic specification. Protection of electrostatic sensitive devices. Requirements for clean room areas |
| EN 100015-4:1994 |
Basic specification. Protection of electrostatic sensitive devices. Requirements for high voltage environments |
| EN 10002-1:2001 |
Tensile testing of metallic materials. Method of test at ambient temperature |
| EN 10002-5:1992 |
Tensile testing of metallic materials. Method of test at elevated temperatures |
| EN 100114-1:1994 |
Rule of Procedure 14. Quality assessment procedures. Approval of manufacturers and other organizations |
| EN 100114-1:1997 |
Rule of Procedure 14. Quality assessment procedures. CECC requirements for the approval of an organization |
| EN 100114-6:1997 |
CECC Quality assessment procedure for electronic components. Technology approval of electronic component manufacturers |
| EN 10016-1:1995 |
Non-alloy steel rods for drawing and/or cold rolling. General requirements |
| EN 10016-2:1995 |
Non-alloy steel rods for drawing and/or cold rolling. Specific requirements for general purpose rod |
| EN 10016-3:1995 |
Non-alloy steel rods for drawing and/or cold rolling. Specific requirements for rimmed and rimmed substitute low carbon steel rod |
| EN 10016-4:1995 |
Non-alloy steel rods for drawing and/or cold rolling. Specific requirements for rod for special applications |
| EN 10017:2004 |
Steel rod for drawing and/or cold rolling. Dimensions and tolerances |
| EN 10020:2000 |
Definition and classification of grades of steel |
| EN 10021:1993 |
General technical delivery requirements for steel and iron products |
| EN 10024:1995 |
Hot rolled taper flange I sections. Tolerances on shape and dimensions |
| EN 10025-1:2004 |
Hot rolled products of non-alloy structural steels. General delivery conditions |
| EN 10025-2:2004 |
Hot rolled products of non-alloy structural steels. Technical delivery conditions for flat products |
| EN 10025-3:2004 |
Hot rolled products of non-alloy structural steels. Technical delivery conditions for long products |
| EN 10025-4:2004 |
Hot-rolled products of structural steels. Technical delivery conditons for the thermomechanical rolled weldable fine grain steels |
| EN 10025-5:2004 |
Hot rolled products of structual steels. Technical delivery conditons for structural steels with improved atmospheric corrosion resistance |
| EN 10025-6:2004 |
Hot rolled products of structural steels. Technical delivery conditons for plates and wide flats of high yield strength structural steels in the quenched and tempered condition |
| EN 10027-1:1992 |
Designation systems for steel. Steel names, principal symbols |
| EN 10027-2:1992 |
Designation systems for steels. Steel numbers |
| EN 10028-1:2000 |
Specification for flat products made of steels for pressure purposes. General requirements |
| EN 10028-2:2003 |
Specification for flat products made of steels for pressure purposes. Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10028-3:2003 |
Specification for flat products made of steels for pressure purposes. Weldable fine grain steels, normalized |
| EN 10028-4:2003 |
Specification for flat products made of steels for pressure purposes. Nickel alloy steels with specified low temperature properties |
| EN 10028-5:2003 |
Specification for flat products made of steels for pressure purposes. Weldable fine grain steels, thermomechanically rolled |
| EN 10028-6:2003 |
Specification for flat products made of steels for pressure purposes. Weldable fine grain steels, quenched and tempered |
| EN 10028-7:2000 |
Flat products made of steels for pressure purposes. Stainless steels |
| EN 10029:1991 |
Specification for tolerances on dimensions, shape and mass for hot rolled steel plates 3 mm thick or above |
| EN 10031:2003 |
Semi finished products for forging. Tolerances on dimensions shape and mass |
| EN 10034:1993 |
Structural steel I and H sections. Tolerances on shape and dimensions |
| EN 10036:1991 |
Chemical analysis of ferrous materials. Determination of total carbon in steels and irons. Gravimetric method after combustion in a stream of oxygen |
| EN 1004:2004 |
Mobile access and working towers made of prefabricated elements. Materials, dimensions, design loads, safety and performance requirements |
| EN 10045-1:1990 |
Charpy impact test on metallic materials. Test method (V- and U-notches) |
| EN 10045-2:1993 |
Charpy impact test on metallic materials. Method for the verification of impact testing machines |
| EN 10048:1997 |
Hot rolled narrow steel strip. Tolerances on dimensions and shape |
| EN 10051:1992 |
Specification for continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels. Tolerances on dimensions and shape |
| EN 1005-1:2001 |
Safety of machinery. Human physical performance. Terms and definitions |
| EN 10052:1994 |
Vocabulary of heat treatment terms for ferrous products |
| EN 1005-2:2003 |
Safety of machinery. Human physical performance. Manual handling of machinery and component parts of machinery |
| EN 1005-3:2002 |
Safety of machinery. Human physical performance. Recommended force limits for machinery operation |
| EN 10055:1996 |
Hot rolled steel equal flange tees with radiused root and toes. Dimensions and tolerances on shape and dimensions |
| EN 10056-1:1999 |
Specification for structural steel equal and unequal angles. Dimensions |
| EN 10056-2:1993 |
Specification for structural steel equal and unequal angles. Tolerances on shape and dimensions |
| EN 10058:2003 |
Hot rolled flat steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 |
Hot rolled square steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
| EN 10060:2003 |
Hot rolled round steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
| EN 10061:2003 |
Hot rolled hexagon steel bars for general purposes. Dimensions and tolerances on shape and dimensions |
| EN 10067:1997 |
Hot rolled bulb flats. Dimensions and tolerances on shape, dimensions and mass |
| EN 10071:1991 |
Chemical analysis of ferrous materials. Determination of manganese in steels and irons. Electrometric titration method |
| EN 1007-1:2002 |
Advanced technical ceramics. Ceramic composites. Methods of test for reinforcements. Determination of size content |
| EN 1007-2:2002 |
Advanced technical ceramics. Ceramic composites. Methods of test for reinforcements. Determination of linear density |
| EN 1007-3:2002 |
Advanced technical ceramics. Ceramic composites. Methods of test for reinforcements. Determination of filament diameter and cross-section area |
| EN 1007-5:2003 |
Advanced technical ceramics. Ceramic composites. Methods of test for reinforcements. Determination of distribution of tensile strength and of tensile strain to failure of filament |
| EN 10079:1993 |
Definition of steel products |
| EN 1008:2002 |
Mixing water for concrete. Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry. |
| EN 10083-1:1991 |
Quenched and tempered steels. Technical delivery conditions for special steels |
| EN 10083-2:1991 |
Quenched and tempered steels. Technical delivery conditions for unalloyed quality steels |
| EN 10083-3:1996 |
Quenched and tempered steels. Technical delivery conditions for boron steels |
| EN 10084:1998 |
Case hardening steels. Technical delivery conditions |
| EN 10085:2001 |
Nitriding steel. Technical delivery conditions |
| EN 10087:1999 |
Free cutting steels. Technical delivery conditions for semi-finished products, hot rolled bars and rods |
| EN 10088-1:2005 |
Stainless steels. List of stainless steels |
| EN 10088-2:2005 |
Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 10088-3:2005 |
Stainless steels. Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 10089:2002 |
Hot rolled steels for quenched and tempered springs. Technical delivery conditions |
| EN 10090:1998 |
Valve steels and alloys for internal combustion engines |
| EN 10092-1:2003 |
Hot rolled spring steel flat bars. Flat bars. Dimensions and tolerances on shape and dimensions |
| EN 10092-2:2003 |
Hot rolled spring steel flat bars. Ribbed and grooved spring leaves. Dimensions and tolerances on shape and dimensions |
| EN 10095:1999 |
Heat resisting steels and nickel alloys |
| EN 1010-1:2004 |
Safety of machinery. Safety requirements for the design and construction of printing and paper converting machines. Common requirements |
| EN 1010-3:2002 |
Safety of machinery. Safety requirements for the design and construction of printing and paper converting machines. Cutting machines |
| EN 1010-4:2004 |
Safety of machinery. Safety requirements for the design and construction of printing and paper converting machines. Bookbinding, paper converting and finishing machines |
| EN 10106:1996 |
Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state |
| EN 10107:1996 |
Grain-oriented electrical steel sheet and strip delivered in the fully processed state |
| EN 10108:2004 |
Round steel rod for cold heading and cold extrusion. Dimensions and tolerances |
| EN 10111:1998 |
Continuously hot-rolled low carbon steel sheet and strip for cold forming. Technical delivery conditions |
| EN 1011-1:1998 |
Welding. Recommendations for welding of metallic materials. General guidance for arc welding |
| EN 1011-2:2001 |
Welding. Recommendations for welding of metallic materials. Arc welding of ferritic steels |
| EN 1011-3:2000 |
Welding. Recommendations for welding of metallic materials. Arc welding of stainless steels |
| EN 1011-4:2000 |
Welding. Recommendations for welding of metallic materials. Arc welding of aluminium and aluminium alloys |
| EN 1011-5:2003 |
Welding. Recommendations for welding of metallic materials. Welding of clad steel |
| EN 1011-7:2004 |
Welding. Recommendations for welding of metallic materials. Electron beam welding |
| EN 1011-8:2004 |
Welding. Recommendations for welding of metallic materials. Welding of cast irons |
| EN 10120:1997 |
Steel sheet and strip for welded gas cylinders |
| EN 1012-1:1997 |
Compressors and vacuum pumps. Safety requirements. Compressors |
| EN 1012-2:1997 |
Compressors and vacuum pumps. Safety requirements. Vacuum pumps |
| EN 10126:1996 |
Cold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state |
| EN 10130:1999 |
Cold-rolled low-carbon steel flat products for cold forming. Technical delivery conditions |
| EN 10131:1991 |
Cold-rolled uncoated low carbon and high yield strength steel flat products for cold forming. Tolerances on dimensions and shape |
| EN 1013-1:1998 |
Light transmitting profiled plastic sheeting for single skin roofing. General requirements and test methods |
| EN 1013-2:1999 |
Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) |
| EN 10132-1:2000 |
Cold rolled narrow steel strip for heat treatment. Technical delivery conditions. General |
| EN 10132-2:2000 |
Cold rolled narrow steel strip for heat treatment. Technical delivery conditions. Case hardening steels |
| EN 10132-3:2000 |
Cold rolled narrow steel strip for heat treatment. Technical delivery conditions. Steels for quenching and tempering |
| EN 10132-4:2000 |
Cold rolled narrow steel strip for heat treatment. Technical delivery conditions. Spring steels and other applications |
| EN 1013-3:1998 |
Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements and test methods for sheets of polyvinyl chloride (PVC) |
| EN 1013-4:2000 |
Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements, test methods and performance of polycarbonate (PC) sheets |
| EN 1013-5:2000 |
Light transmitting profiled plastic sheeting for single skin roofing. Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets |
| EN 10136:1991 |
Chemical analysis of ferrous materials. Determination of nickel in steels and irons. Flame atomic absorption spectrometric method |
| EN 10139:1998 |
Cold rolled uncoated mild steel narrow strip for cold forming. Technical delivery conditions |
| EN 10140:1997 |
Cold rolled narrow steel strip. Tolerances on dimensions and shape |
| EN 1014-1:1995 |
Wood preservatives. Creosote and creosoted timber. Methods of sampling and analysis. Procedure for sampling creosote |
| EN 1014-2:1996 |
Wood preservatives. Creosote and creosoted timber. Methods of sampling and analysis. Procedure for obtaining a sample of creosote from creosoted timber for subsequent analysis |
| EN 10143:1993 |
Continuously hot-dip metal coated steel sheet and strip. Tolerances on dimensions and shape |
| EN 1014-3:1998 |
Wood preservatives. Creosote and creosoted timber. Methods of sampling and analysis. Determination of the benzo[$ia]pyrene content of creosote |
| EN 1014-4:1996 |
Wood preservatives. Creosote and creosoted timber. Methods of sampling and analysis. Determination of the water extractable phenols content of creosote |
| EN 10149-1:1996 |
Specification for hot-rolled flat products made of high yield strength steels for cold forming. General delivery conditions |